DETERMINATION OF THE FLOWING BOTTOM-HOLE PRESSURE OF A VERTICAL WELL FROM SURFACE PRESSURE AND WELL PARAMETERS


DETERMINATION OF THE FLOWING BOTTOM-HOLE PRESSURE OF A VERTICAL WELL FROM SURFACE PRESSURE AND WELL PARAMETERS

Abstract

The pressure measured in a well at or near the depth of the producing formation. For well-test purposes, it is often desirable to refer the pressure to a datum level chosen at a reference depth by calculating the pressure that would occur if the pressure measurement were made at the datum level rather than at the actual depth of the gauge. Knowledge of this pressure is fundamental in determining the most efficient methods of recovery and the most efficient lifting procedure, yet there is less information about these pressures than about any other part of the general problem of producing oil.

This research project is thus a study on the determination of the flowing bottom-hole pressure of a vertical well from surface pressure and well parameters

Chapter one of the study lays a theoretical framework for subsequent chapters.  Following the general introduction, the problem statement and the objective of the study which provided the basis for the significance of the study were also highlighted.

In the literature review as contained in chapter two, works of various authors, international and local journals were reviewed to elicit views on the determination of the flowing bottom-hole pressure of a vertical well from surface pressure and well parameters.

Chapter three, research methodology, Model Derivation and Development, Model Assumptions, Model Modification and Solution Method were highlighted.

Chapter four was based on result and discussion. This chapter was sub-divided into raw data analysis and result analysis.

Finally, chapter five was divided into recommendation and conclusion.

TABLE OF CONTENTS

Title Page    -    -    -    -    -    -    -    -    -    i

Approval Page    -    -    -    -    -    -    -    -    ii

Declaration    -    -    -    -    -    -    -    -    iii

Dedication    -    -    -    -    -    -    -    -    -    iv

Acknowledgement    -    -    -    -    -    -    -    v

Abstract    -    -    -    -    -    -    -    -    -    vi

Table of Contents    -    -    -    -    -    -    -    vii

CHAPTER ONE – INTRODUCTION

1.1    Background of the Study    -    -    -    -    -    -    -

1.1 BACKGRAND OF STUDY-    -    -    -    -    -    -    -    -

1.2 STATEMENT OF THE PROBLEM-    -    -    -    -    -    -   

1.3 AIM& OBJECTIVES-     -    -    -    -    -    -    -    -

1.4SIGNIFICANCE OF STUDY-    -    -    -    -    -    -    -    -

1.5SCOPE OF WORK-        -        -    -    -    -    -    -    -        

CHAPTER TWO

2.1 Literature Review-        -        -               -     -    -    -    -    

CHAPTER THREE – RESEARCH METHODOLOGY

3.1    Introduction    -    -    -    -    -    -    -    -    -

3.0    METHODOLOGY-     -    -    -    -    -    -    -    -

3.1    Model Derivation and Development-        -    -    -    -    -

3.2    Model Assumptions-    -    -    -    -    -    -    -    -

3.3    Model Modification-    -    -    -    -    -    -    -    -

3.4    Solution Method-    -    -    -    -    -    -    -    -    -

CHAPTER FOUR – DATA PRESENTATION AND ANALYSIS

4.0    Introduction    -    -    -    -    -    -    -    -    -

4.0    RESULT AND DISCUSSION-    -    -    -    -    -    -    -

4.1    Raw Data Analysis-    -    -    -    -    -    -    -    -

4.2    Result Analysis-    -    -    -    -    -    -    -    -    -

CHAPTER FIVE – CONCLUSION AND RECOMMENDATION

5.0    Conclusion and Recommendation    -    -    -    -    -    -   

5.1    Conclusion    -    -    -    -    -    -    -    -    -    -

5.2    Recommendations    -    -    -    -    -    -    -    -

    References -    -    -    -    -    -    -    -    -    -

CHAPTER1

1.0 INTRODUCTION

1.1 BACKGRAND OF STUDY

Interpretation of data from Well test analysis has been based on the implicit assumption that the reservoir is a homogeneous single layer. However, the real petroleum reservoir, is a composition of layers with unique interlayer characteristics. The individual layers are usually separated from each other by an interface which could be either permeable or impermeable. Pressure behavior in this kind of vertically heterogeneous system is not necessarily like that of a single layered system and seldom reveals more than the average properties of the entire system. It is against this backdrop that this study became necessary.  Well completion in such systems would be more instructive, enabling better reservoir and production engineering practice if detailed layer information is available at it prime. The petroleum industry is however interested in accurately calculating the pressure losses that occur for multiphase flow in the tubing and pipelinesArnarson, K., Karlsdóttir, R., Eysteinsson, H., Flovenz, Ó.G and Guðlaugsson S.Þ. (2008).

Accurate predictions of pressure losses in pipes would enable proper design. Also, pressure determination in a production system in the petroleum industry is very important as it helps in the effective production of oil and gas from the reservoir but of all, the most important is the determination of flowing bottom-hole pressure as its knowledge helps in the determination of so many parameters needed for efficient production and also to avert early depletion of the reservoir. Its knowledge can also be used to prevent formation damage which could be caused by early sand production in the reservoirArnórsson, S. (1995).

Surface pressures often can be converted to bottom-hole values if adequate information is available about the wellbore system.

1.1.1 WHAT IS BOTTOM HOLE FLOWING PRESSURE

The pressure at the bottom of a working oil, water, or gas well (the Great Soviet Encyclopedia, 1979). The pressure measured in a well at or near the depth of the producing formation. For well-test purposes, it is often desirable to refer the pressure to a datum level chosen at a reference depth by calculating the pressure that would occur if the pressure measurement were made at the datum level rather than at the actual depth of the gauge(Schlumberger oilfield glossary).A knowledge of this pressure is fundamental in determining the most efficient methods of recovery and the most efficient lifting procedure, yet there is less information about these pressures than about any other part of the general problem of producing oil (Millikan and Sidwell, 1930). As earlier said, the bottom-hole pressure can be determined from surface pressures like the well head pressure if adequate information is available about the production system which can be easily gotten from well testing operations (Economides, 1979). Since the well head pressure and parameters are easily gotten from pressure transient analysis whose success depends on the accurate measurement or estimation of bottom-hole pressure (Omohimoria and Ayodele, 2013), it is therefore desirable and necessary to obtain the bottom-hole pressure from these data. This will be carried out in order to further highlight the advantages which are associated with having adequate knowledge about the bottom-hole pressure of a reservoir.

1.1.2 TYPICAL FLOW REGIMES

 At certain position and time in the reservoir different flow behaviors are usually encountered in the reservoir. This gives rise to different flow regimes. Flow regimes are usually classified according to the rate of change of pressure with respect to time and position

 Steady-state

During steady-state flow, the pressure does not change with time. This is observed for example when a constant pressure effect, such as resulting from a gas cap or some types of water drive, ensures a pressure maintenance in the producing formation. Pressure usually will changes from one point to the other in the reservoir algebraically,

Image…………………………………………1.1

Pseudo steady state

The pseudo steady state regime characterizes a closed system response. With a constant rate production, the drop of pressure becomes constant for each unit of time.

Image……………………….. 1.2

Where k is a constant.  In practice, this can be reached more easily than the steady state.

 Transient state

Transient responses are observed before constant pressure or closed boundary effects are reached. The pressure variation with time is a function of the well geometry and the reservoir properties, such as permeability and heterogeneity. It can be expressed mathematically as,

Image………………………….. 1.3

Image

Usually, well test interpretation focuses on the transient pressure response. Near wellbore conditions are seen first and later, when the drainage area expands, the pressure response is characteristic of the reservoir properties until boundary effects are seen at late time (then the flow regime changes to pseudo steady or steady state). The applications of the steady-state flow to describe the flow behavior of several types of fluid in different reservoir geometries are presented below. These include:

• Linear flow of incompressible fluids

• Linear flow of slightly compressible fluids

• Linear flow of compressible fluids

 • Radial flow of incompressible fluids

 • Radial flow of slightly compressible fluids

 • Radial flow of compressible fluids

 • Multiphase flow

1.1.3 VerticalMultiphase flow

Much has been written in the literature regarding the multiphase flow of fluids in pipe. This problem is much more complex than the single-phase flow problem because there is the simultaneous flow of both liquid (oil or condensate and water) and vapor (gas). The mechanical energy equation Image  is the basis for methods to estimate the pressure drop under multiphase flow; however, the problem is in determining the appropriate velocity, friction factor, and density to be used for the multiphase mixture in the calculation. In addition, the problem is further complicated as the velocities, fluid properties, and the fraction of vapor to liquid change as the fluid flows to the surface due to pressure changes.

Many researchers have proposed methods to estimate pressure drops in multiphase flow. Each method is based on a combination of theoretical, experimental, and field observations, which has led some researchers to relate the pressure-drop calculations to flow patterns. Flow patterns or flow regimes relate to the distribution of each fluid phase inside the pipe. This implies that a pressure calculation is dependent on the predicted flow pattern. There are four flow patterns in the simplest classification of flow regimes:

⦁    Bubble flow

⦁    Slug/Plug flow

⦁    Churn flow

⦁    Annular-mist flow

Bubble: (Fig...) This type of flow was noted to occur at very low gas velocities.  This type of flow is characterized by bubbles of gas moving along the upper part of pipe at approximately the same velocity as the liquid.

Slug/Plug flow: (Fig…) In this type of flow, the flow of liquid is basically restricted due to the amount of gases which evolve from the liquid phase and collage to form slug-like gas pockets. Like the bubbly flow, the liquid phase is the continuous phase but in this case, the gas phase overrides the liquid phase.

Churn flow /Semi-annular: (Fig...) It is characterized by secondary currents set up by the velocity gradients in the liquid causing the liquids to climb the tube walls and, aided by waves, to coalesce at the top.  The amount of liquid in the bottom of the tube was greater than at top and walls, hence the name semi-annular.

Annular: (Fig...) This type of flow is characterized by liquid flowing in a thin film around the entire inside face of the pipe, the gas flowing at a high velocity as a central core.  The liquid is flowing in a continuous annular rings, hence the name annular flow.

Figure 1.1.3 above (Taitel, Bornea and Duckler, 1980) shows the various flow regimes that could be expected in vertical flow as a function of the superficial velocities of gas and liquid flow

1.2 STATEMENT OF THE PROBLEM

A calculation method for predicting Bottom Hole Pressure (BHP) based on easily obtainable wellhead parameter has been the preferred method in the oil and gas industry. But the predictive capability of the existing correlations is a thing of concern to the oil industry operators. This is due to the inability of the existing models and correlations to account for the presence of sand particles in the flow stream; also, the requirement for the well to be shut-in for BHP predictions is counterproductive.

1.3 AIM& OBJECTIVES

The aim of the project is to determine the flowing bottom-hole pressure of a vertical well from surface pressure and well parameters. This will be done by the modification of the general energy equation considering only the frictional pressure term. The modified equation (derived model) will be validated with a well data which will be gotten from a company.

The objectives of determining the flowing bottom-hole pressure of a well from well head pressure and well head data include the following:

⦁    Efficient interpretation of the behavior of the underground system.

⦁    Determination of BHP helps in provision of important information for efficient production, avert early depletion and early sand production in the reservoir.

⦁    Determination of the most efficient methods of recovery and the most efficient lifting procedures.

⦁    Determination of pressure losses in pipes and tubing for proper design of Artificial Lift Systems - Gas Lift, ESP’s etc.

⦁    Production Optimization - Identification of production bottlenecks, Gaslift optimization, and completion designs.

1.4 SIGNIFICANCE OF STUDY

This study provides a better and economic guide on how flowing bottom-hole pressure can be estimated from well head pressure and well head data and also considers time. In order words, the estimation method delivers results quickly without much expenses, unlike directly measuring the BHP with down-hole pressure gauges which is much more expensive.

1.5 SCOPE OF WORK

The main focus of this research is limited to the estimation of flowing bottom-hole pressure (BHP) for a vertical well from well head pressure (Surface pressure) and well head data which will be obtained from a company. It will show how pressure can be determined mathematically from the available data through modelling using MATLAB. It should be noted that this study is a modification of Guo’s systematic model for flowing bottom-hole pressure predictions.

.

DETERMINATION OF THE FLOWING BOTTOM-HOLE PRESSURE OF A VERTICAL WELL FROM SURFACE PRESSURE AND WELL PARAMETERS



TYPE IN YOUR TOPIC AND CLICK SEARCH.






RESEARCHWAP.COM
Researchwap.com is an online repository for free project topics and research materials, articles and custom writing of research works. We’re an online resource centre that provides a vast database for students to access numerous research project topics and materials. Researchwap.com guides and assist Postgraduate, Undergraduate and Final Year Students with well researched and quality project topics, topic ideas, research guides and project materials. We’re reliable and trustworthy, and we really understand what is called “time factor”, that is why we’ve simplified the process so that students can get their research projects ready on time. Our platform provides more educational services, such as hiring a writer, research analysis, and software for computer science research and we also seriously adhere to a timely delivery.

TESTIMONIES FROM OUR CLIENTS


Please feel free to carefully review some written and captured responses from our satisfied clients.

  • "Exceptionally outstanding. Highly recommend for all who wish to have effective and excellent project defence. Easily Accessable, Affordable, Effective and effective."

    Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.
  • "I saw this website on facebook page and I did not even bother since I was in a hurry to complete my project. But I am totally amazed that when I visited the website and saw the topic I was looking for and I decided to give a try and now I have received it within an hour after ordering the material. Am grateful guys!"

    Hilary Yusuf, United States International University Africa, Nairobi, Kenya.
  • "Researchwap.com is a website I recommend to all student and researchers within and outside the country. The web owners are doing great job and I appreciate them for that. Once again, thank you very much "researchwap.com" and God bless you and your business! ."

    Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.
  • "I love what you guys are doing, your material guided me well through my research. Thank you for helping me achieve academic success."

    Sampson, University of Nigeria, Nsukka.
  • "researchwap.com is God-sent! I got good grades in my seminar and project with the help of your service, thank you soooooo much."

    Cynthia, Akwa Ibom State University .
  • "Great User Experience, Nice flows and Superb functionalities.The app is indeed a great tech innovation for greasing the wheels of final year, research and other pedagogical related project works. A trial would definitely convince you."

    Lamilare Valentine, Kwame Nkrumah University, Kumasi, Ghana.
  • "Sorry, it was in my spam folder all along, I should have looked it up properly first. Please keep up the good work, your team is quite commited. Am grateful...I will certainly refer my friends too."

    Elizabeth, Obafemi Awolowo University
  • "Am happy the defense went well, thanks to your articles. I may not be able to express how grateful I am for all your assistance, but on my honour, I owe you guys a good number of referrals. Thank you once again."

    Ali Olanrewaju, Lagos State University.
  • "My Dear Researchwap, initially I never believed one can actually do honest business transactions with Nigerians online until i stumbled into your website. You have broken a new legacy of record as far as am concerned. Keep up the good work!"

    Willie Ekereobong, University of Port Harcourt.
  • "WOW, SO IT'S TRUE??!! I can't believe I got this quality work for just 3k...I thought it was scam ooo. I wouldn't mind if it goes for over 5k, its worth it. Thank you!"

    Theressa, Igbinedion University.
  • "I did not see my project topic on your website so I decided to call your customer care number, the attention I got was epic! I got help from the beginning to the end of my project in just 3 days, they even taught me how to defend my project and I got a 'B' at the end. Thank you so much researchwap.com, infact, I owe my graduating well today to you guys...."

    Joseph, Abia state Polytechnic.
  • "My friend told me about ResearchWap website, I doubted her until I saw her receive her full project in less than 15 miniutes, I tried mine too and got it same, right now, am telling everyone in my school about researchwap.com, no one has to suffer any more writing their project. Thank you for making life easy for me and my fellow students... Keep up the good work"

    Christiana, Landmark University .
  • "I wish I knew you guys when I wrote my first degree project, it took so much time and effort then. Now, with just a click of a button, I got my complete project in less than 15 minutes. You guys are too amazing!."

    Musa, Federal University of Technology Minna
  • "I was scared at first when I saw your website but I decided to risk my last 3k and surprisingly I got my complete project in my email box instantly. This is so nice!!!."

    Ali Obafemi, Ibrahim Badamasi Babangida University, Niger State.
  • To contribute to our success story, send us a feedback or please kindly call 2348037664978.
    Then your comment and contact will be published here also with your consent.

    Thank you for choosing researchwap.com.