MODIFICATION OF AN EXISTING METAL SHEET-BENDING MACHINE


Department Of Mechanical Engineering


PAGES: 0
FORMAT: MS WORD
Chapters: 1-5
PRICE: ₦ 5,000.00

MODIFICATION OF AN EXISTING METAL SHEET-BENDING MACHINE   

ABSTRACT

The metal bending machine is designed to be manually operated. The bending machine with working capacity to complete a 900 fold of a full-length plate (8 ft = 2400mm) and up to 2.5mm thickness. The construction is based on initial machine design, materials. The machine can be used to perform any type of bending. It consist of heavy beams which are coupled together to bring about any shape of bending after the flat sheet has been marked out to specified dimensions. It serves as invaluable equipment because it offers solution to the technology of sheet metals in Nigeria. 

TABLE OF CONTENT

PAGES

Front page………………………………………………………………………… i

Certification………………………………………………………………………..      ii-iii

Dedication……………………………………………………………………… iv

Acknowledgement……………………………………………………………. V

Abstract……………………………………………………………………………. vi

Table of content……………………………………….……………………      vii-ix

Project topic……………………………………………………………………. 1

Aim……………………………………………………………………………….. 1

Procedures………………………………………………………………………. 1

Selected materials…………………………………………………………… 2

Equipment………………………………………………………………………… 3

CHAPTER ONE

1.0 INTRODUCTION................................................................ 4

1.1 Importance of Sheet Metal Work and Bending Machines .  4-9

1.2 Historical Review and Classification of Bending Machines. 9-12

1.3 Operational Characteristic of the Bending Machine………. 12-14

CHAPTER TWO

2.0 BENDING TECHNOLOY…………………………………………………………………. 15

2.1 Principles of Bending………………………………………………. 15-17

2.2 The mechanics of Bending……………………………………….. 17-19

2.3 Plastic Deformation Due to Bending…………………………… 20-21

2.4 Spring Back……………………………………………………………… 21-22

2.5 Method for Compensating Spring Back…………………… 22-16

2.6 Method of Determining Angle of Spring Back……………… 26-27   

CHAPTER THREE

3.0 DESIGN CONSIDERATION………………………………………… 28

3.1 Bending Stress……………………………………………………………  28-31

3.2 Material Selections………………………………………………………… 32

3.2.1 Physical Properties of Metal………………………………………….  32-33

3.2.2 Mechanical Properties of Metal……………………………………..  34-38

3.3 Material Selection Table………………………………………………..  39

CHAPTER FOUR 

4.0 COMPONENT DESIGH, CONSTUCTION, 

CHAPTER FIVE

5.0 ANALYSIS…………………………………………………………………… 54

5.1 Construction………………………………………………….…………….. 55

5.2 Anticipated Faults and Corrections…………….………………..… 55-56

5.3 Maintenance…………………………………………………………………56-57

5.4 Conclusion……………………………………………………………………. 57

5.5 Recommendations………………………………………………………… 58

References……………………………………………………………………

PROJECT TOPIC:

DESIGN AND CONDTRUCTION OF A METAL SHEET-BENING MACHINE Component 

AIM:

To design and construct a mental sheet-bending machine component which is manually operated. A machine with working capacity to complete a 90o fold of a full-length plate (8ft = 2400mm) and up to 2.5mm thickness.

PROEDURES:

These are the procedures for designing and constructing a metal sheet-bending machine.

⦁ Initial Machine Design 

⦁ Materials Selection

⦁ Costing

⦁ Purchasing of the selected Materials

⦁ Equipment Used for the Construction

SELECTED MATERIALS

Gauge Dimension

⦁ 4mm plate - 1200 x 1200mm

⦁ H Channel (8inch x 5inch) - 2.550mm

⦁ 12mm Plate (8ft x 1ft) - 2.850mm

⦁ 12mm Plate - 304 x 2550mm

⦁ 50mm Plate - 2,352 x 588mm

⦁ Æ 40mm Shaft - 2550mm

⦁ 2” x 2” Angle Bar - 2 lengths (18ft)

⦁ Æ 30mm Shaft - 40mm

⦁ Metal Weight - 40kg

⦁ Electrodes (Gauge 10) - 2 Packets

⦁ Bolts/ Nuts - Different Sizes

⦁ Hydro lift out crucible furnace 

EQUIPMENTS

⦁ Moulding flask

⦁ Hack Saw

⦁ Grinding Stones

⦁ Cutting Stone

⦁ Shearing Machine

⦁ Arc Welding Machine

⦁ Drilling Machine

⦁ Grinding Machine

⦁ Lathe Machine

⦁ Metal Bending Machine

⦁ Shapping machine 

⦁ Muilding machine 

⦁ Driving machine

⦁ Feed taping tool 

CHAPTER ONE

1.0 INTRODUCTION

1.1 Importance of Sheet Metal Work and Bending Machine

What is a metal? It is a strong shinny, which conducts electricity and melts when you make it hot enough. But surely metal must be something more than this because there are other substances such as carbon,, glass and rubbers, which are, obviously not metals but can also variously claim to have strength, elasticity or electrical conductivity.

Furthermore, most of the metals will melt when heated sufficient. What then is a metal? A study of simple metallurgy will show that there is one important factor, which distinguishes metals from non-metals and that is the neat, orderly arrangement of the atoms into regular geometric molecules. Metal is a good conductor of heat and electricity and forming basic oxides.

An alloy is a fused mixture or compound of two or more pure metals. The reasons for making these mixtures are many and various. Pure metals have certain desirable properties but are often lacking in other ways. Therefore it is necessary to mix other metals with them in order to preserve and improve their basic properties. To quote a well known example: Aluminum is a light weight metal which makes it useful for aircraft construction, but it is also soft and weak so a small quantity of copper is added to it to give the necessary strength and rigidity (Courtesy, 1980).

The subsequent development of iron and steel to suit its use in various forms enables it to serve effectively wherever used. Iron and steel remains the most vastly used material for structural works, enclosures and packages.  

The most popular forms of iron and steel remains the sheet form, mostly used in enclosure and vessel fabrication. The term metal sheet refers to lighter gauges of steel in rolled form ranging in thickness from approximately 0.4mm to 3.2mm. (Surenda singh, 1979).

Many engineering components are produced from flat sheets of metal which are cut to shape and then folded to form the finished article. The edges are then secured by a variety of methods such as welding, soldering and riveting. The accuracy of the size of drawing the shape on the flat sheet know as the development. Allowance is made at this stage for folding or bending, the amount varying with the radius of the bend and the metal thickness.

Quite a large of sheet metal is employed in the manufacturing industries, in building of aircrafts, automobiles and household appliances. Sheet metal to a large extent is used in the building industries for roofing, heating, prefabricated structures and air conditioning casings. 

The base metal iron and bronze were appreciated for their strength especially for weapons and tools; copper, tin and lead came to be used mainly for their utility or durability- for cooking, for storage or for strengthening wooden construction of any kind.

The particular property of metals that can be mixed or alloyed in various combinations and proportions to make a better materials for particular purposes was understood in the ancient world. Copper and tin produces bronze; copper and zinc produces brass; lead and tin produces pewter. This property has been exploited with ingenuity and increasing scientific knowledge while the designation iron, copper, lead, silver and gold are still commonly used (Surenda, 1979).

All metals shares certain characteristic: a uniform smooth complexion; great strength and tenacity; but also easily worked surface; and malleability (their capacity to assume any desired shape).

All these are carried out with the help of sheet metal works, which involves fabrication of metallic objects by cutting, forming/ bending and fastening, welding etc. are referred as sheet metal works. (Oyewole and Agada, 2000).

The term bending refers to an operation in which metal is deflected from its original form to a new position generally at an angle or a curve and it remains so permanently. Bending is a common metalworking technique to process sheet metal. It is usually done by hand on a box and pan brake, or industrially on a press brake. Typical products that are made like this are boxes; such as electrical enclosures, rectangular ductwork and some firearm parts.

Usually, bending has to overcome both tensile stress as well as comprehensive stress. When bending is done the residual stresses make it spring back towards its original position, so we have to over bend the sheet metal keeping in mind the residual stresses.

The machine used for bending operation is called sheet metal bending machine. This machine can be used to perform any type of bending. It consists of heavy beams, which are coupled together to bring about any shape of bending after the flat sheet has been marked out to a specific dimension of bending. This machine is extensively used in our community today by steel fabricators and production workshops for the fabrication of iron gates, security doors, burglary proofs, Louvre frames etc. (Oyewole and Agada 2000).

The street metal bending machine has great importance. It is used for bending metal sheet into shape and it is also used for giving out design.

1.2 Historical Review and Classification of Bending Machines 

Over the years tremendous efforts have been made both in the study, design and development of tolls and machinery employed in manipulating sheet metal into desired shape mostly by bending.

The earliest approach to bending sheet metal to desire shape involves the use of stakes (thick or strong sharpened stick driven into the ground as a support, boundary, mark etc.) alongside hand tools of wood or rubber mallet, bench socket positioned at right angle to the craft-man. Stakes are of different types and forms corresponding from the type of bend to be made. The finishing achieved from this is generally poor and not very accurate. It’s other dements lie in the much labour required and limitation of the length of the sheet that can be bent.

To overcome these demerits and boost the fabrication industry, machine to carry out the bending operation were thereby developed. Bending machine in use include pinch bending rolls, power operated pyramid rolls, lock forming machine, Timman’s Jenny, Swing beam. The cramp folding machine; had operated geared bending machine, the box is the most versatile and easy to operate of all bending machines.

A top Vee-shaped blade descends on the plate, forming the necessary bend in vee- shaped bottom die. Top blades could be in varying width thus allowing box forms to be produced.

V shape die

Image

Fig 1.1: The press brake

The swing beam is a manually operated bending machine and it is extensively used in our community today by steel fabricators and production workshops. It is extensively used because it does not require electricity. The swing beam bending machine is easy to operate and it can bend a metal sheet of about 2.5mm.

DESIGN

The sheet metal bending machine that is designed and reported here is the swing beam type consisting of a clamping beam, bending beam, machine bed, supporting frame and the bend

1. Balance weight

2. Removable finger

3. Finger  adjustment screw

4. Clamping lever 

5. Bending blade 

6. Adjustable stop

7. Frame

8. Clamping beam adjustment 

9. Bending lever 

10. Tie bar 

11. Bending beam adjustment 

Image

Fig 1.2: Sketch o a metal the machine

1.3 Operation  Characteristic of the Bending Machine

The design is such that will carry out vee-shape angle bend on a sheet metal of maximum thickness of 2.5mm and maximum width of 8ft (2 1 . e. a standard sheet metal plate length. A sheet metal thickness above 2.5mm cannot be bend by this machine but can be bent by a press brake. Press brake may be of either mechanical or hydraulic operation i.e. the power to drive the press is by a flywheel or by hydraulic rams (khurmi and Gupta, 1979).

1. The essential components of the bending machine are:

2. Clamping beam with threaded shaft, it hold the sheet metal to the machine bed.

3. Machine bed, it houses the sheet to be bent.

4. Bending beam, this ensures the folding of the sheet metal.

5. Pedestal, it supports the entire machine.

Turning the threaded shaft anti-clockwise, the bending beam lift up and an opening created, then, metal strip can be slotted into the machine for bending. Turning the shaft clockwise the bending beam comes or clamp down onto the machine bed, the sheet is clamped in between the clamping beam and the machine bed. By lifting the folding handle /bending lever up, the sheet metal bends into shape. The handle is released, the shaft (threaded) is turned anti-clockwise and the sheet is removed.

A back gauge is provided to control the length of sheet that enters into the machine for bedding in case where sheets to be cut are smaller in length between the back gauge and the bending zone. Metal sheets are measured and marked; the marked portion is placed alongside the edge of the folding blade.

.



TYPE IN YOUR TOPIC OR KEYWORD AND CLICK SEARCH:

HOW TO GET YOUR COMPLETE PROJECT MATERIAL INSTANTLY

  • * Select 3 free project topics of your choice from your Department

    * Submit the 3 project topics to your Supervisor for his or her Approval

    * Call our 24/7 customer service desk or WhatsApp Chat# (+234) 0803-766-4978 and get your project topics and complete material instantly.

    * You can also send an Email to [email protected]

    * All project materials on this website are well researched by professionals with high level of professionalism.


TESTIMONIES FROM OUR CLIENTS

Please feel free to carefully review some written and captured responses from our satisfied clients.


  • Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.

    "Exceptionally outstanding. Highly recommend for all who wish to have effective and excellent project defence. Easily Accessable, Affordable, Effective and effective."

  • Hilary Yusuf, United States International University Africa, Nairobi, Kenya.

    "I saw this website on facebook page and I did not even bother since I was in a hurry to complete my project. But I am totally amazed that when I visited the website and saw the topic I was looking for and I decided to give a try and now I have received it within an hour after ordering the material. Am grateful guys!"

  • Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.

    "Researchwap.net is a website I recommend to all student and researchers within and outside the country. The web owners are doing great job and I appreciate them for that. Once again, thank you very much "researchwap.net" and God bless you and your business! ."

  • Lamilare Valentine, Kwame Nkrumah University, Kumasi, Ghana.

    "Great User Experience, Nice flows and Superb functionalities.The app is indeed a great tech innovation for greasing the wheels of final year, research and other pedagogical related project works. A trial would definitely convince you."

  • Sampson, University of Nigeria, Nsukka.

    "I love what you guys are doing, your material guided me well through my research. Thank you for helping me achieve academic success."

  • Cynthia, Akwa Ibom State University .

    "researchwap.com is God-sent! I got good grades in my seminar and project with the help of your service, thank you soooooo much."

  • Elizabeth, Obafemi Awolowo University

    "Sorry, it was in my spam folder all along, I should have looked it up properly first. Please keep up the good work, your team is quite commited. Am grateful...I will certainly refer my friends too."

  • Ali Olanrewaju, Lagos State University.

    "Am happy the defense went well, thanks to your articles. I may not be able to express how grateful I am for all your assistance, but on my honour, I owe you guys a good number of referrals. Thank you once again."

  • Willie Ekereobong, University of Port Harcourt.

    "My Dear Researchwap, initially I never believed one can actually do honest business transactions with Nigerians online until i stumbled into your website. You have broken a new legacy of record as far as am concerned. Keep up the good work!"

  • Theressa, Igbinedion University.

    "WOW, SO IT'S TRUE??!! I can't believe I got this quality work for just 5k...I thought it was scam ooo. I wouldn't mind if it goes for over 5k, its worth it. Thank you!"

  • Joseph, Abia state Polytechnic.

    "I did not see my project topic on your website so I decided to call your customer care number, the attention I got was epic! I got help from the beginning to the end of my project in just 3 days, they even taught me how to defend my project and I got a 'B' at the end. Thank you so much researchwap.com, infact, I owe my graduating well today to you guys...."

  • Christiana, Landmark University .
    Christiana, Landmark University .

    "My friend told me about ResearchWap website, I doubted her until I saw her receive her full project in less than 15 miniutes, I tried mine too and got it same, right now, am telling everyone in my school about researchwap.com, no one has to suffer any more writing their project. Thank you for making life easy for me and my fellow students... Keep up the good work"

  • Musa, Federal University of Technology Minna

    "I wish I knew you guys when I wrote my first degree project, it took so much time and effort then. Now, with just a click of a button, I got my complete project in less than 15 minutes. You guys are too amazing!."

  • Ali Obafemi, Ibrahim Badamasi Babangida University, Niger State.

    "I was scared at first when I saw your website but I decided to risk my last 5k and surprisingly I got my complete project in my email box instantly. This is so nice!!!."


  • To contribute to our success story, send us a feedback or please kindly call 2348037664978.
    Then your comment and contact will be published here also with your consent.
    Thank you for choosing researchwap.com.

FREQUENTLY ASKED QUESTIONS

  • 1. How can I get the complete project if I order?

    AFTER FOLLOWING THE PAYMENT PROCEDURES HERE, AND WE RECEIVE YOUR DETAILS AS SMS ON 08037664978 or as mail to [email protected], THE MATERIAL WILL BE ATTACHED AND MAILED TO YOUR EMAIL ADDRESS WITHIN 30 MINUTES, AND A NOTIFICATION OF THE DELIVERY WILL BE SENT TO YOUR PHONE NUMBER.

    2. How will my payment be confirmed?

    FOLLOW THE PAYMENT INSTRUCTIONS FOUND ON THE PAYMENTS PAGE. NOTE: Payment information is required for Payment Confirmation.

    3. One of your topics suites my project, but the case study is different. What step should I take?

    Students are always advised to use our materials as guide. However, if you have a different case study, you may need to consult researchwap.com Depending on similarity of the organization/industry (case study) you may modify to, if you wish.

    4. How long does it take to get the complete project?

    Depending on how fast your payment and details is acknowledged by us, you will get the complete project within 30 minutes. However, on a very good day you can still get it within 15 minutes!

    5. Why should I trust this website?

    We are well aware of fraudulent activities (scam) that have been happening on the internet. It is unfortunate, but hopefully declining. However, we wish to re-assure our esteemed clients that we are genuine and our services is authentic, if not, we would not post our account details, email address, phone number or any personal details that could be traceable. Free chapter 1 is always given on the site to prove to you that we got the material. If you are unable to view the free chapter 1 send an email or SMS containing your name, topic, with the subject head "FREE CHAPTER 1" to [email protected] or 08037664978 plus the topic. You will get the free chapter 1 within an hour.

    6. Do you accept ATM payments and Online Transfers?

    Yes. We accept ATM transfers and online payments. FOLLOW THE PAYMENT INSTRUCTIONS FOUND ON THE PAYMENTS PAGE.

    7. Is it a complete research project or just materials?

    Yes it is a complete research project. We send complete project materials (i.e. chapters 1-5, full references, and questionnaires/secondary data to your email address after payment confirmation.

    8. How can I pay Online with my ATM card?

    1. Visit an ATM

    2. Insert your card

    3. Select Quickteller

    4. Select "Pay bills"

    5. Choose your account type

    6. Select "Others"

    7. Enter 322222 as the payment code

    8. Enter your phone number as "Customer Reference"

    9. Accept the N1.00 amount displayed

    10. Follow prompts to complete the transaction

    9. How will I receive a software?

    A link to download the software will always be on the first page of the material.

    10. I have a fresh topic that is not on your site. How do I go about it?

    We have professional writers in management sciences, computer science and social sciences. If you have a fresh topic, just click this hire a writer link, fill the form, submit the details and one of our writers will contact you shortly.


PROJECT DETAILS

PAGES: 0
FORMAT: MS WORD
Chapters: 1-5
PRICE: ₦ 5,000.00


TYPE TOPIC OR KEYWORD AND CLICK SEARCH: