GEOMETRIC DESIGN OF HIGHWAY


Department Of Civil Engineering


PAGES: 80
FORMAT: MS WORD
Chapters: 1-5
PRICE: ₦ 5,000.00

GEOMETRIC DESIGN OF HIGHWAY

ABSTRACT

Geometric design of highways is an important factor to be considered before highway construction as it necessitates the determination of specific design elements, which include: the number of lanes, lane width, median and width, length of acceleration and deceleration lanes for on and off ramps, need for truck climbing lanes for steep grades, curve radii required for vehicle turning and the alignment required to provide adequate stopping and passing sight distances.  This project work focuses mainly on highway horizontal and vertical alignments which are the most important components of geometric design and intersection. These project works also discusses geometric design of cross section,, sight distance, procedures for highway alignment and the comprehensive plan and profile detailing using manual and automated then comparing the result.

TABLE OF CONTENT

                                                                                              PAGES

Title page…………………………………………………………………………...    

Certification………………………………………………………………………...........i

Dedication……………………………………………………………………………......ii

Acknowledgement……………………………………………………………….............iii

Abstract………………………………………………………………………..…............iv

Table of contents…………………………………………………………….……………v

List of Tables……………………………………………………………………………...viii

List of Figures……………………………………………………………………………..ix

CHAPTER ONE: INTRODUCTION

1.1    Historical Background of Road ……………………………………………………....1

1.2    The Purpose of Highway ………………………………………………………..……2 

1.3    Geometric Design  ………………………………………………………………..…..3

1.4    Classification of Roads …………………………………………………………….....4

1.5    Background and purpose ……………………………………………………………..5

1.6    Aim and Objectives of the study …………………………………………..................6

1.7    Scope of Study ………………………………………..................................................6 

1.8    Outline of Study ………………………………………………………………………6

CHAPTER TWO: LITERATURE REVIEW

2.0.1 Past Research Work on Highway Geometric DESIGN ……………....................7

2.1    Design Element………………………………………………………………………...17

         2.1.1  Design Speed …………………………………………………………………...18

         2.1.2   Design Vehicle …………………………………………………………………21

         2.1.3   Sight Distance ………………………………………………………………….22

         2.1.4   Horizontal Alignment…………………………………………………………...32

         2.1.5   Vertical Alignment……………………………………………………………...33

          2.1.6    Capacity………………………………………………………………………..34

2.2    Road Survey  ………………………………………………………………………...…35

         2.2.1   Reconnaissance Survey………………………………………………………….35

         2.2.2   Preliminary Location Survey……………………………………………………35

         2.2.3    Final Location Survey…………………………………………………………..36

2.3    Total Station ……………………………………………………………………………36

          2.3.1   Advantages of total station ……………………………………………………..37

          2.3.2   Disadvantages of total station …………………………………………………..37

2.4    Computer Aided Design ………………………………………………………………..38

         2.4.1   AutoCad Civil 3D ……………………………………………………………….38

         2.4.2   Advantages of CAD over manual Drawing ……………………………………..39

         2.4.3   Highway Engineering Software………………………….....................................39

2.5    Safety…………………………………………………………………………………....40

CHAPTER THREE: METHODOLOGY

3.1    Description of the case-study road ……………………………………………………...42

3.2    Alignment ……………………………………………………………………………….44

3.3    Vertical curves ………………………………………………………………………..…47

          3.3.1   Sag vertical curve ……………………………………………………………….47

           3.3.2   Crest vertical curve ……………………………………………………………..48

3.4    Horizontal curve …………………………………………………………………………49

3.5    Typical example on the calculation of horizontal curve ………………………………...51

3.6    Road Design in Civil 3D (Automated Design) ………………………………………….51

CHAPTER FOUR: RESULT AND DATA ANALYSIS

4.1      Horizontal Curves………………………………………………………………………54

4.2 Vertical Curves………………………………………………………………...………55

4.3       Comparison of horizontal curves results……………………………………………….68

4.4 Comparisons of vertical curves results………………………………………………...69  4.5 Discussion of results.......................................................................................................72

CHAPTER FIVE: SUMMARY AND CONCLUSION

5.1 Summary……………………………………………………………………………….73

5.2 Conclusion……………………………………………………………………………..74

            References……………………………………………………………………………..75

LIST OF TABLES

Table 2.1 Passing sight distance                                                                                          11

Table 2.2 Minimum sight distance used on highway design                                               25

Table 2.3 Sight distance-rural roads (British practice)                                                        29

Table 2.4 Sight distance-urban roads (British practice)                                                      29

Table 2.5 Advantages of Automated drawing over Manual drawing                                 38

Table 4.1 Horizontal curves computation results                                                                58

Table 4.2 Vertical curves computation results (Sample)                                                     59

Table 4.3 Comparison of horizontal curves results                                                             60

Table 4.4 Comparison of vertical curves parameter results                                                60

LIST OF FIGURES

Figure 2.1 Presentation of horizontal curve images for comparison                        12

Figure 2.2 Sight distance for vehicle turning left from major road                           26

Figure 2.3 Decision sight distance model                                                                 28

Figure 2.4 Minimum stopping sight distance (Crest curve)                                     29

Figure 2.5 Minimum stopping sight distance (Sag curve)                                        30

Figure 2.6 Passing sight distance                                                                               31

Figure 3.1 Google map showing the location of the case study area                        48

Figure 3.2 Vertical curve terminology (Profile view shown)                                   52

Figure 3.3 Geometry of the circle                                                                             53

Figure 3.4 Relationship between the degree of curve (D) and the circle                  54

Figure 4.1 Graph showing the difference in the K (Rate of vertical                         62

curvature) value of manual and automated  

Figure 4.2 Graph showing the difference in the LC (length of Chord)                     63

value of manual and automated

Figure 4.3: Graph showing the difference in the TL (Tangent   63

length) value of manual and automated 

Figure 4.4: Graph showing the difference in the finished level value                       64

of manual, automated and existing level

                                                                   CHAPTER ONE

1. INTRODUCTIONSince the attainment of independence, Nigeria has witnessed rapid economic and social development, which has open up the need for travelling between cities which led to increase in the need for good and safe road.Highway is any public road or other public way on land; the term exists in distinction to waterway also can said to be high-speed roads designed to connect major cities. A highway is a major road for any form of motor transport which vehicles and the public in general may lawfully pass without license. A road on the other hand is a way for vehicle and other types of traffic (human or animal) which may or may not be lawfully usable to the public at large. Highways are vitally important to a country’s economic development. The construction of a high quality road network directly increases a nation’s economic output by reducing journey times and costs, making a region more attractive economically. The actual construction process will have the added effect of stimulating the construction market. Roads could be considered as a cause and the consequence of civilization, as they both precede and follow it. 

1.1 HISTORICAL BACKGROUND OF ROAD

The need for road construction came up with the invention of the wheel some 5000 years ago. Prior to this invention, people and transportation beast simply moved on tracks which were only wide enough for their comfort. With the invention of the wheel, there was the need for improvement on the existing tacks to provide firmer and wider surfaces with better riding qualities to accommodate higher volume of traffic. These improvements were carried out in order to increase the safety and speed of conveying people and goods from one place to another for social and commercial purposes.

Road transport is one of the most common mode of transport. Roads in the form of track ways, human pathways etc. were used even from the pre-historic times. Since then many experiments were going on to make the riding safe and comfort. Thus road construction became an inseparable part of many civilizations and empires.  The need for road construction came up with the invention of the wheel some decades ago. Prior to this invention, people and transportation beast simply moved on tracks which were only wide enough for their comfort. With the invention of the wheel, there was the need for improvement on the existing tacks to provide firmer and wider surfaces with better riding qualities to accommodate higher volume of traffic. These improvements were carried out in order to increase the safety and speed of conveying people and goods from one place to another for social and commercial purposes.

There are many different types of highways. Highways differ primarily in the amount of access control they have and, therefore, in the amount of traffic they are designed to carry. Highway with fully controlled access can handle the most traffic and are built to the highest construction standards. Inter-state highways. Vehicles that enter or exit these types of highway can do so only at certain points along the highway, generally by using special entrance and exit ramps. The ramps allow vehicle to access the road without disturbing the flow of traffic. Incoming vehicles must merge with flowing traffic, and vehicles leaving the highway use exit ramps that guide them off the highway without blocking the traffic behind. Intersections with other roads are avoided by using either bridge known as overpasses to carry one roadway under another. Finished strips called shoulders on the edges of highways allow drivers of disabled vehicles to make repairs or await assistance without blocking traffic.

1. THE PURPOSE OF  HIGHWAYThe purpose of the highway is to provide a means of reducing the stress or pressure due to a wheel load to the minimum value which the ground under the structure can support. This is why materials of the highest strength are used for the surface. Other purposes of highway are listed below:

⦁ It provide a skid resistance surface

⦁ It provide wider riding surface to accommodate anticipated traffic volume

⦁ It provide a firmer riding surface ands

⦁ It provide a smooth riding surface

⦁ It provide efficient and convenient movement of people and goods from one place to another.The intensity of the stress is greatest at the surface of the road and it is distributed in a pyramid from down the depth of the formation. As long as the stress reaching the sub grade does not exceed the resistance put forth by the sub grade, there will be no distortion or damage to the road surface.

1.3 GEOMETRIC DESIGN

Geometric design is defined as the design or proportioning of the visible elements of the street or highway. The geometry of the roadway is of central importance since it provides the framework for the design of other highway elements. In addition, the geometric design establishes the basic nature and quality of the vehicle path, which has a primary effect upon the overall safety characteristics of the street or highway.

The design of roadway geometry must be conducted in close coordination with other design elements. These other elements include: pavement design, roadway lighting, traffic control devices, transit, drainage, and structural design. The design should consider safe roadside clear zones, bicycle and pedestrian safety accommodation, emergency response, and maintenance capabilities.

The geometric design of highways deals with the dimensions and layout of visible features like of the highway. The emphasis of the geometric design is to address the requirement of the driver and the vehicle such as safety, comfort, efficiency, etc. The features normally considered are the cross section elements, sight distance consideration, horizontal curvature, gradients, and intersection. The design of these features is to a great extend influenced by driver behavior and psychology, vehicle characteristics, traffic characteristics such as speed and volume. Proper geometric design will help in the reduction of accidents and their severity. Therefore, the objective of geometric design is to provide optimum efficiency in traffic operation and maximum safety at reasonable cost. The planning cannot be done stage wise like that of a pavement, but has to be done well in advance. The main components that will be discussed are:

⦁ Design speed

⦁ Design vehicle

⦁ Safety 

⦁ Sight distance

⦁ Alignment

⦁ CapacityThe safety characteristics of the design should be given primary consideration. The initial establishment of sufficient right of way and adequate horizontal and vertical alignment is not only essential from a safety standpoint, but also necessary to allow future upgrading and expansion without exorbitant expenditure of highway funds.

1.4 CLASSIFICATION OF ROADS

Roads can be classified in many ways. The classification based on speed and accessibility is the most generic one. Note: As the accessibility of road increases, the speed reduces. Accordingly, the roads can classify as follows in the order of increased accessibility and reduced speeds.

⦁ Freeways

⦁ Expressways

⦁ Highways

⦁ Arterials

⦁ Local streets

⦁ Collector’s streets

⦁ Freeways: Freeways are access controlled divided highways. Most freeways are four lanes, two lanes each direction, but many freeways widen to incorporate more lanes as they enter urban areas. Access is controlled through the use of interchanges, and the type of interchange depends upon the kind of intersecting road way (rural roads, another freeway etc.)

⦁ Expressways: They are superior type of highways and are designed for high speeds (120 km/hr. is common), high traffic volume and safety. They are generally provided with grade separations at intersections. Parking, loading and unloading of goods and pedestrian traffic is not allowed on expressways.

⦁ Highways: They represent the superior type of roads in the country. Highways are of two types – rural highways and urban highways. Rural highways are those passing through rural areas (villages) and urban highways are those passing through large cities and towns, i.e. Urban areas.

⦁ Arterials: It is a general term denoting a street primarily meant for through traffic usually on a continuous route. They are generally divided highways with fully or partially controlled access. Parking, loading and unloading activities are usually restricted and regulated. Pedestrians are allowed to cross only at intersections/designated pedestrian crossings.

⦁ Local streets: A local street is the one which is primarily intended for access to residence, business or abutting property. It does not normally carry large volume of traffic and also it allows unrestricted parking and pedestrian movements.

⦁ Collector’s streets: These are streets intended for collecting and distributing traffic to and from local streets and also for providing access to arterial streets. Normally full access is provided on these streets. There are few parking restrictions except during peak hours.

1.5BACKGROUND AND PURPOSE

Highway geometry should be designed for vehicle traffic safety and efficiency, particularly on the trunk roads or Expressways on which traffic function must be most important. Though the design policy was established, the prerequisites of design have been imaginary or extremely limited. For example, minimum radius of horizontal curve is defined with design speed, super elevation and side slip friction factor. The actual operating speed must correspond to something speed, but it did not work well to be used for design purpose of road geometry, or did not calibrated enough because of the difficulty of data acquisition. Such an estimation model should have a feature including driver’s perception and behavior.

1.6   AIM AND OBJECTIVES OF THE STUDY 

The aim of the study is to perform the geometric design of a selected case study road. 

And comparison between Manual and Automated design.

The objectives required to achieve the above aim include:

⦁ Design of all vertical alignment components

⦁ Design of all horizontal alignment components

⦁ Comprehensive plan and profile detailing of the case study road.1.7    SCOPE OF STUDY

The scope of this study covers the geometric design of highway at Anka road, bukkuyum L.G.A Zamfara State. Using manual design and comparing with automated design.

1.8 OUTLINE OF STUDY

For a proper understanding of this project report it has been divided into five chapters. 

Chapter one introduced the project; chapter two discusses the relevant literature in respect to this project. Chapter three contains the design methods of highway designed detail. Chapter four contains the result and analysis and finally recommendations and conclusion based on findings is shown in chapter five.

.



TYPE IN YOUR TOPIC OR KEYWORD AND CLICK SEARCH:

HOW TO GET THE COMPLETE PROJECT MATERIAL ON GEOMETRIC DESIGN OF HIGHWAY

  • * Click the green DOWNLOAD Button above

    * Select any option to get the complete project material instantly.

    * Chat our 24/7 customer service desk on WhatsApp# (+234) 0803-766-4978 and get your complete project material instantly.

    * All project materials on this website are well researched by professionals with high level of professionalism.


TESTIMONIES FROM OUR CLIENTS

Please feel free to carefully review some written and captured responses from our satisfied clients.


  • Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.

    "Exceptionally outstanding. Highly recommend for all who wish to have effective and excellent project defence. Easily Accessable, Affordable, Effective and effective."


  • Hilary Yusuf, United States International University Africa, Nairobi, Kenya.

    "I saw this website on facebook page and I did not even bother since I was in a hurry to complete my project. But I am totally amazed that when I visited the website and saw the topic I was looking for and I decided to give a try and now I have received it within an hour after ordering the material. Am grateful guys!"


  • Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.

    "Researchwap.net is a website I recommend to all student and researchers within and outside the country. The web owners are doing great job and I appreciate them for that. Once again, thank you very much "researchwap.net" and God bless you and your business! ."


  • Lamilare Valentine, Kwame Nkrumah University, Kumasi, Ghana.

    "Great User Experience, Nice flows and Superb functionalities.The app is indeed a great tech innovation for greasing the wheels of final year, research and other pedagogical related project works. A trial would definitely convince you."


  • Sampson, University of Nigeria, Nsukka.

    "I love what you guys are doing, your material guided me well through my research. Thank you for helping me achieve academic success."


  • Cynthia, Akwa Ibom State University .

    "researchwap.com is God-sent! I got good grades in my seminar and project with the help of your service, thank you soooooo much."


  • Elizabeth, Obafemi Awolowo University

    "Sorry, it was in my spam folder all along, I should have looked it up properly first. Please keep up the good work, your team is quite commited. Am grateful...I will certainly refer my friends too."


  • Ali Olanrewaju, Lagos State University.

    "Am happy the defense went well, thanks to your articles. I may not be able to express how grateful I am for all your assistance, but on my honour, I owe you guys a good number of referrals. Thank you once again."


  • Willie Ekereobong, University of Port Harcourt.

    "My Dear Researchwap, initially I never believed one can actually do honest business transactions with Nigerians online until i stumbled into your website. You have broken a new legacy of record as far as am concerned. Keep up the good work!"


  • Theressa, Igbinedion University.

    "WOW, SO IT'S TRUE??!! I can't believe I got this quality work for just 5k...I thought it was scam ooo. I wouldn't mind if it goes for over 5k, its worth it. Thank you!"


  • Joseph, Abia state Polytechnic.

    "I did not see my project topic on your website so I decided to call your customer care number, the attention I got was epic! I got help from the beginning to the end of my project in just 3 days, they even taught me how to defend my project and I got a 'B' at the end. Thank you so much researchwap.com, infact, I owe my graduating well today to you guys...."


  • Christiana, Landmark University .

    "My friend told me about ResearchWap website, I doubted her until I saw her receive her full project in less than 15 miniutes, I tried mine too and got it same, right now, am telling everyone in my school about researchwap.com, no one has to suffer any more writing their project. Thank you for making life easy for me and my fellow students... Keep up the good work"


  • Musa, Federal University of Technology Minna

    "I wish I knew you guys when I wrote my first degree project, it took so much time and effort then. Now, with just a click of a button, I got my complete project in less than 15 minutes. You guys are too amazing!."


  • Ali Obafemi, Ibrahim Badamasi Babangida University, Niger State.

    "I was scared at first when I saw your website but I decided to risk my last 5k and surprisingly I got my complete project in my email box instantly. This is so nice!!!."


  • To contribute to our success story, send us a feedback or please kindly call 2348037664978.
    Then your comment and contact will be published here also with your consent.
    Thank you for choosing researchwap.com.

FREQUENTLY ASKED QUESTIONS

  • How can I get the complete project - GEOMETRIC DESIGN OF HIGHWAY

    Simply click on the DOWNLOAD green button above and follow the procedure stated.


    Is it a complete project work or just materials?

    Yes, it's a Complete Research Project material. i.e Chapters 1-5, Abstract, Table of Contents, Full References, Questionnaires / Secondary Data


    What if I want to change the case study for GEOMETRIC DESIGN OF HIGHWAY, What can i do?

    Chat with Our 24/7 Customer Service Desk Now: WhatsApp# and you will be responded to Instantly


    How long does it take to get the complete project on GEOMETRIC DESIGN OF HIGHWAY?

    Depending on how fast your payment and details is acknowledged by us, you will get the complete project within 30 minutes. However, on a very good day you can still get it within 15 minutes!


    How will I get my complete project?

    The Complete Project Material will be Delivered via your Email Address in an MS Word document format


    Can I get my Complete Project through WhatsApp?

    Yes! We also send your Complete Research Project to your WhatsApp Number


    What if my Project Supervisor made some changes to a topic i picked from your website?

    Call or Chat With Our 24/7 Custumer Care Desk: +2348037664978 and you will be responded to Instantly


    Do you assist students with Assignment, Term Paper, Seminar and Project Proposal?

    Call or Chat With Our 24/7 Custumer Care Desk: +2348037664978 and you will be responded to Instantly


    What if i do not have any project topic idea yet?

    Don't Worry! We've Got Your Covered. Chat with us on WhatsApp# (+234) 0803-766-4978 to Get Instant Help.


    Why should I trust this website?

    We are well aware of fraudulent activities that have been happening on the internet. It is regrettable, but hopefully declining. However, we wish to reinstate to our esteemed clients that we are genuine and duly registered with the Corporate Affairs Commission as "TOPNOTCH INFOTECH ENTERPRISE". This site runs on Secure Sockets Layer (SSL), therefore all transactions on this site are HIGHLY secure and safe!


    I have a fresh topic that is not on your site. How do I go about it?

    Don't Worry, Chat with us on WhatsApp# (+234) 0803-766-4978 to Get Instant Help.



PROJECT DETAILS

PAGES: 80
FORMAT: MS WORD
Chapters: 1-5
PRICE: ₦ 5,000.00




TYPE TOPIC OR KEYWORD AND CLICK SEARCH: