GAS DEHYDRATION USING TRIETHYLENE GLYCOL (A CASE STUDY OF SHELL, UGHELI)


GAS DEHYDRATION USING TRIMETHYLENE GLYCOL (A CASE STUDY OF SHELL, UGHELI) 

TABLE OF CONTENT

Title Page………………..i

Certification………….…ii

Dedication………………iii

Acknowledgement……….iv

Table of content……...…v

CHAPTER ONE

INTRODUCTION

1.1       NATURAL GAS DEHYDRATION PROCESSES

1.11     REFRIGERATION

1.12     ADSORPTION

1.13     ABSORBTION

1.2     STATEMENT OF PROBLEM

1.3     AIMS AND OBJECTIVES

1.4     SCOPE AND LIMITATIONS

1.5     METHODOLOGY

1.6     CASE STUDY

CHAPTER TWO

LITERATURE REVIEW

2.1     SURFACE PRODUCTION FACILITIES

2.2     GAS LIQUID SEPARATION

2.3     GAS SWEETENING

2.4     GAS DEHYDRATION

2.5     ORIGIN OF WATER IN NATURAL GAS

2.6.     REASONS FOR DEHYDRATING NATURAL GAS

2.7.     METHODS OF GAS DEHYDRATION

2.7.1     REFRIGERATION

2.7.2     ADSORPTION DEHYDRATION

2.7.3     ABSORPTION DEHYDRATION

CHAPTER THREE

METHODOLOGY

3.1. BRIEF HISTORY AND LOCATION OF THE UTOROGU GAS PLANT

3.2. FLOW DESCRIPTION OF THE UTOROGU GAS PLANT

3.3 EQUIPMENT DESCRIPTION

3.3.1   The Inlet Manifold

3.3.2 Contactor Column

3.3.3. Glycol Flash Tank

3.3.4. Rich TEG Mechanical Filter

3.3.5. Lean/Rich TEG Exchanger

3.3.6. TEG Reboiler and Still (Stripper) Column

3.3.7. The Reflux Condenser

3.3.8. Lean TEG Circulation Pumps

3.3.9. Dry Gas/Lean Glycol Heat Exchanger

3.4. OPERATIONAL PROBLEMS IN A GLYCOL PLANT

3.4.1 Insufficient Dehydration

3.4.2 Foaming

3.4.3 Pump Failure

3.4.4 Vapourization Loss

3.4.5 Salt Contamination

3.4.6 Corrosion from Acid Gases

3.4.7 Glycol Degradation

3.4.8 Emission Problem

3.5   PRESENTATION OF DATA

3.5.1   INLET GAS TEMPEARTURE

3.5.2   LEAN TEG TEMPERATURE

3.5.3   REBOILER TEMPERATURE

3.5.4   STRIPPING GAS FLOWRATE

3.5.5 LEAN GLYCOL CIRCULATION

CHAPTER FOUR

ANALYSIS AND INTERPRETATION OF RESULTS

4.1   INLET GAS TEMPERATURE

4.2   LEAN TEG TEMPERATURE

4.3   REBOILER TEMPERATURE

4.4   STRIPPING GAS FLOWRATE

4.5   LEAN GLYCOL CIRCULATION RATE

4.6   GLYCOL LOSSES

4.7     SOLUTIONS TO THE OPERATIONAL AND GLYCOL LOSS PROBLEMS IN A GLYCOL PLANT

4.7.1   Insufficient Dehydration in the Absorber

4.7.2       Foaming

4.7.3     Pump Failure

4.7.4      Vapourization Loss

4.7.5    Salt Contamination

4.7.6     Glycol Degradation

4.7.7    Corrosion from Acid Gases

4.7.8 SOLUTIONS TO EMMISSION PROBLEMS

4.7.8.1 Optimizing Glycol Circulation Rate

4.7.8.2 Installation of Flash Tank Separator

4.7.8.3 Electric Pump Installation

4.7.8.4 Optimizing Stripping Gas Rate

CHAPTER FIVE

CONCLUSION AND RECOMMENDATION

5.1    CONCLUSION

5.2 RECOMMENDATIONS     

REFERENCES

CHAPTER ONE

INTRODUCTION

Natural gas is a combustible gaseous mixture of gaseous hydrocarbons, very light liquid hydrocarbons, free water, water vapour and other undesirable non – hydrocarbon gaseous and solid compounds found in conventional natural gas reservoirs as non-associated gas (NAG), as associated gas (AG) or as gas condensates.

 Associated gas or gas-wellhead-gas is found in contact with oil in the reservoir and is produced with the oil and separated at the casing head or wellhead whereas non- associated gas contains little or no natural gas liquids (oil) at reservoir condition and it is termed dry gas or lean gas if the fluid at the surface still remains gas. However if the surface pressure cause some liquid hydrocarbon to evolve, it is called a wet gas or rich. Condensate occurs not as liquid or gas but as a very dense and high pressure fluid due to its high pressure and high temperature reservoir condition.

Natural gas may also occur in tight sands, tight shales, methane gas occluded in coal, as gas hydrates in geo-pressurized acquifer and as deep gas. These gases are more technologically difficult or more expensive to produce than conventional gas and are termed non- conventional natural gas.

Hydrocarbon majorly contained in the natural gas mixtures are methane and ethane which exist as gaseous components, propane and butane existing as volatile fluid, pentane, small amount of hexanes and heavier components existing as liquid components. Typical non- hydrocarbon which may exist in the gas stream are solid particles, water vapour or free water, mercury, formaldehyde, benzene, toluene, ethyl benzene and  xylene (collectively referred to as BTEX), undesirable gases such as carbon oxides, sulfur gases and nitrogen oxides (collectively called acid gases), oxygen, helium and naturally occurring radioactive materials such as radon.

                           Table 1.0:      Typical composition of Natural gas

         Name                               Formula                Volume (%)

 Methane                               CH4                                   >85

Ethane                                  C2H6                                  3-8

Propane                                C3H8                        1-2

Butane                                  C4H10                                 <1

Pentane                                C5H12                                  <1

Carbon dioxide                     CO2                                 1-2

Hydrogen sulfide                  H2O                        <1

Nitrogen                                N2                                       1-5

Helium                                  He                        <0.5

Mercury                                Hg                       Traces

Benzene                               C6H6                     Traces

Toulene                                C7H8                     Traces

Xylene                               C6H4(CH3)2            Traces

Natural gas is a fossil fuel composed almost entirely of methane. The composition of natural gas varies depending on the field, formation, or reservoir from which it is extracted. Natural gas which contains acid gases above customer’s specification is termed sour gas while Natural gas containing acid gas below customer’s specification or no acid gas is termed sweet gas.

Natural gas is a fossil fuel formed by either the biogenic or thermogenic degradation of organic matter which has been accumulated over time within the earth’s crust. Biogenic mechanism involves shallow depth and low temperature decomposition of sedimentary organic matter by anaerobic bacterials whereas thermogenic mechanism involves deeper depth and high temperature thermal cracking of sedimentary matter or oil into gas. Natural gas being a fossil fuel is today, one of the most important fuels in our lives as it is the source of energy for household, industrial and commercial use, as well as to generate electricity.

Natural, associated or tail gas usually contains water, in liquid and/or vapour form, at source and/or as a result of sweetening with an acqueous solution. Operating experience and thorough engineering have proved that it is necessary to reduce and control the water content of gas to ensure safe processing and transmission. This is accomplished by the process of dehydration.

1.1       NATURAL GAS DEHYDRATION PROCESSES

Natural gas dehydration is the removal of water or water vapour from the natural gas stream. Free water in natural gas gives rise to difficulties in production, handling and transmission of natural gas. It is therefore necessary that water be removed from the gas stream as soon as possible.

There are several methods of dehydrating natural gas but the most common of these methods are:

(i)Refrigeration

(ii)Adsorption

(iii)Absorption

1.11     REFRIGERATION

This method employs cooling the natural gas to condense the water molecules to the liquid phase with the subsequent injection of inhibitor to prevent hydrate formation.

1.12     ADSORPTION

This is the removal of water from the gas stream by solid materials called desiccants which take in and hold water molecules within themselves by adhesive forces. Several types of solid desiccant used are silica gel, silica-based beads, activated alumina, activated bauxite, membranes and molecular sieves.     

1.13     ABSORBTION

This is the process whereby water or water vapour is removed or absorbed from the gas stream by intimate contact with a liquid desiccant. Of all the liquid desiccants, the glycols have proved to be the most effective in current use as they approximate the properties that meet commercial application criteria. The glycol with absorbed water is regenerated and re-circulated into dehydration cycle for further water removal.

Chemically, glycol is an aliphatic organic compound belonging to the group of chemicals referred to as dihydric alcohols (diols). Physically, glycols are similar to water in that, they are colourless, clear and odourless liquids. They however possess greater specific gravity and viscosity than water at all temperatures and are soluble in water.

The four types of glycols that have been successfully used to dehydrate natural gas are;

Monoethylene glycol (MEG) Diethylene glycol (DEG) Triethylene glycol (TEG) Tetraethylene glycol (T4EG)

Triethylene glycol has gained nearly universal acceptance as the most cost effective of the glycols due to superior dew point depression, operating cost and operation reliability.

Among the different gas dehydration processes, absorption dehydration is more economically attractive hence has become the most popular method.

1.2       STATEMENT OF PROBLEM

Gas dehydration is a common process in gas treatment plant because water in the presence of acid compounds in natural gas can cause corrosion; water also combines with hydrocarbons to form hydrates which can block valves and pipelines. During an absorption dehydration process of natural gas using tri-ethylene glycol, an appreciable quantity of glycol could be lost and a significant amount of volatile organic compounds emitted during regeneration which may be as a result of operational faults or inadequate plant design. Excessive loss of glycol may lower the efficiency of the dehydration process consequently increasing the cost of dehydrating the gas. VOCs emissions may raise concern from environmental regulatory bodies.

1.3       AIMS AND OBJECTIVES

This project work is aimed at

1.  Analyzing the basic process of gas dehydration using Triethylene Glycol.

2   Studying glycol regeneration process as well as examining the causes of associated glycol loss during the regeneration process with possible solutions proffered.

3.  Examining the causes of Volatile organic compounds emission with possible solutions proffered.

1.4       SCOPE AND LIMITATIONS

1.  Use of TEG for the dehydration of natural gas.

2.  Investigating the Parameters affecting glycol regeneration.

3.  Investigating the parameters influencing BTEX emissions.

1.5       METHODOLOGY

The various units of operation of the plant will be studied. Sensitivity analysis of process parameters such as temperature of inlet gas and inlet TEG, in relation to the degree of dehydration and BTEX emissions will be carried out. Previous works on the subject will also be examined.

1.6       CASE STUDY

The Shell Petroleum Development Company (SPDC) gas compression and dehydration plant in Ughelli will be used as case study to achieve the major objectives of this research work.

CHAPTER FIVE

CONCLUSION AND RECOMMENDATION

5.1    CONCLUSION

Results from the analysis carried out shows that glycol losses in the plant is primarily due to:

1.    Insufficient Dehydration in the Absorber

2.    Foaming

3.    Hydrocarbon solubility in TEG solution

4.    Vapourization loss

5.    Salt contamination

6.    Glycol degradation

7.     Corrosion from acid gases

8.    Overcirculation of stripping gas

Results also show that emissions from the dehydration plant is primarily due to:

1.        Glycol overcirculation

2.        Absence of Flash Tank Separator (FTS)

3.        Use of gas-driven pumps

4.        Overcirculation of stripping gas

Considering an excess glycol loss of 356 605litres per annum from the Utorogu gas plant, it is evident that the plant is not running efficiently. The problem can be treated by one or more of the following:

1.          Turn-around maintenance of the entire glycol plant system

2         Frequent draining and reclaiming of the glycol so as to prevent dissolved salt from exceeding its maximum allowable concentration.

3      Amine solution should be added to the glycol in the reboiler and still column to provide corrosion protection from the acid gases.

4     The reboiler temperature should always be kept below 4020F so as to prevent thermal degradation of the glycol.

5    Liquid hydrocarbon, salts and solids should adequately be separated from the glycol so as to avoid foaming due to chemical contamination.

6    The temperature of the still column and the reboiler pressure should constantly be monitored to prevent glycol losses due to vapourisation or carry over.

7      The circulation of stripping gas should be optimized.

8    Lean TEG temperature should be optimized so as to prevent glycol loss due to vapourization in the absorber.

The problem of emissions can be treated by the following:

1.       Optimizing glycol circulation

2.       Flash Tank Separator Installation

3.       Installing of Electric Pumps

4.       Optimizing stripping gas rate.

5.2 RECOMMENDATIONS    

After finishing this study, it is recommended that detailed study should be carried out on the Drizo process of enhanced glycol regeneration which yields up to 99.99%wt glycol. The cost implications as regard to the benefits should be studied to see if it is a GO or NO GO option.

.


TYPE IN YOUR TOPIC AND CLICK SEARCH.






RESEARCHWAP.COM

Researchwap.com is an online repository for free project topics and research materials, articles and custom writing of research works. We’re an online resource centre that provides a vast database for students to access numerous research project topics and materials. Researchwap.com guides and assist Postgraduate, Undergraduate and Final Year Students with well researched and quality project topics, topic ideas, research guides and project materials. We’re reliable and trustworthy, and we really understand what is called “time factor”, that is why we’ve simplified the process so that students can get their research projects ready on time. Our platform provides more educational services, such as hiring a writer, research analysis, and software for computer science research and we also seriously adhere to a timely delivery.

TESTIMONIES FROM OUR CLIENTS


Please feel free to carefully review some written and captured responses from our satisfied clients.

  • "Exceptionally outstanding. Highly recommend for all who wish to have effective and excellent project defence. Easily Accessable, Affordable, Effective and effective."

    Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.
  • "I saw this website on facebook page and I did not even bother since I was in a hurry to complete my project. But I am totally amazed that when I visited the website and saw the topic I was looking for and I decided to give a try and now I have received it within an hour after ordering the material. Am grateful guys!"

    Hilary Yusuf, United States International University Africa, Nairobi, Kenya.
  • "Researchwap.com is a website I recommend to all student and researchers within and outside the country. The web owners are doing great job and I appreciate them for that. Once again, thank you very much "researchwap.com" and God bless you and your business! ."

    Debby Henry George, Massachusetts Institute of Technology (MIT), Cambridge, USA.
  • "I love what you guys are doing, your material guided me well through my research. Thank you for helping me achieve academic success."

    Sampson, University of Nigeria, Nsukka.
  • "researchwap.com is God-sent! I got good grades in my seminar and project with the help of your service, thank you soooooo much."

    Cynthia, Akwa Ibom State University .
  • "Great User Experience, Nice flows and Superb functionalities.The app is indeed a great tech innovation for greasing the wheels of final year, research and other pedagogical related project works. A trial would definitely convince you."

    Lamilare Valentine, Kwame Nkrumah University, Kumasi, Ghana.
  • "Sorry, it was in my spam folder all along, I should have looked it up properly first. Please keep up the good work, your team is quite commited. Am grateful...I will certainly refer my friends too."

    Elizabeth, Obafemi Awolowo University
  • "Am happy the defense went well, thanks to your articles. I may not be able to express how grateful I am for all your assistance, but on my honour, I owe you guys a good number of referrals. Thank you once again."

    Ali Olanrewaju, Lagos State University.
  • "My Dear Researchwap, initially I never believed one can actually do honest business transactions with Nigerians online until i stumbled into your website. You have broken a new legacy of record as far as am concerned. Keep up the good work!"

    Willie Ekereobong, University of Port Harcourt.
  • "WOW, SO IT'S TRUE??!! I can't believe I got this quality work for just 3k...I thought it was scam ooo. I wouldn't mind if it goes for over 5k, its worth it. Thank you!"

    Theressa, Igbinedion University.
  • "I did not see my project topic on your website so I decided to call your customer care number, the attention I got was epic! I got help from the beginning to the end of my project in just 3 days, they even taught me how to defend my project and I got a 'B' at the end. Thank you so much researchwap.com, infact, I owe my graduating well today to you guys...."

    Joseph, Abia state Polytechnic.
  • "My friend told me about ResearchWap website, I doubted her until I saw her receive her full project in less than 15 miniutes, I tried mine too and got it same, right now, am telling everyone in my school about researchwap.com, no one has to suffer any more writing their project. Thank you for making life easy for me and my fellow students... Keep up the good work"

    Christiana, Landmark University .
  • "I wish I knew you guys when I wrote my first degree project, it took so much time and effort then. Now, with just a click of a button, I got my complete project in less than 15 minutes. You guys are too amazing!."

    Musa, Federal University of Technology Minna
  • "I was scared at first when I saw your website but I decided to risk my last 3k and surprisingly I got my complete project in my email box instantly. This is so nice!!!."

    Ali Obafemi, Ibrahim Badamasi Babangida University, Niger State.
  • To contribute to our success story, send us a feedback or please kindly call 2348037664978.
    Then your comment and contact will be published here also with your consent.

    Thank you for choosing researchwap.com.